Wednesday, August 14, 2013

Roundin' Third???

As of my last post I was making slow but steady progress.  Effort since then has continued to be serious, and progress has become more visible.  Weekly trips up to my dad's, battling bicycle traffic in the Republic and monsoon rains to log 14 hour days in an unusually soggy mountain summer is finally starting to pay off.  September camping is right around the corner, but things appear on track.  Over the last month, I learned I need at least 3 trips to the DMV and a certified VIN inspection (after assembly) to title the trailer, so no time to waste.  If you recall as of last time, I was embroiled in wiring and paneling, and I can proudly say those tasks are now substantively done.  Woohoo!!!  Moving forward, focus is shifting toward kitchen door hardware and exterior skin.  Here are the details.

To mount some of the LED fixtures at downward angles, my dad fabricated wedge blocks from CPVC to serve as an angled base:


 Mounted, they make for a clean looking fixture:


Coupled with another light, they provided pretty good kitchen lighting for the current draw:


Moving from the LED fixtures to the strip lighting, if you recall from last time, I purchased an awesome 21 color LED strip light from Home Depot.  Made by Armacost, this light features a wall mounted controller, preset modes, adjustable brightness, and an IR remote control.  Splitting the strip in half (using a pair of scissors), fabricating a wiring extension from a pair of phone cords, and mounting using a pair of u-shaped clear plastic channels and 3M backing tape, the lights came out awesome:



To finish it off, my dad made a nice backing plate for the light controller:


Complementing the strip lights on the inside are a couple of swiveling wall reading lights from Camping World:


Shown in some of the pictures above, is the further finish of the paneling, using the Braden Cherry and lath screws from Home Depot.  Also show is PVC quarter round molding to finish off the edges of the paneling.  Finishing the paneling also included fitting paneling inside the cabinets, which proved a little trickier and more time consuming than expected:


Along the way of finishing the paneling, a measuring miscue resulted in an otherwise very nice looking two part interior door paneling on the kitchen door:


Beyond paneling, work on the kitchen door also included installing gas struts and latch hardware.  After some shopping contemplation, combined with brain wracking over installation, at set of RV Designer gas props from Camping World go on:



Also on the kitchen door, a locking T-handle latch and a pair of chain bolts go on, joined with wire rope and turnbuckles:




Strike plates will go on next to finish the door latches.  Details in the next post.

Changing gears again, remember the wiring?  In addition to the lighting, a couple of 12 volt outlets seemed a good idea- something handy to have.  Combining outlets from Camping World with 110V-120V using a custom wall plate looks pretty good:


In the kitchen, two plates do the job:


With this wiring complete (along with an under cabinet light, some battery wiring, and ground wiring details to follow), the electric raceway and 12V block are looking full:


Ok...I'm running out of gas for this post.  A couple of other details for now- a trip to a truck repair center buys 22' of aluminum roofing coil for the exterior finish, and a used memory foam mattress moves out of my garage to be cut with an electric carving knife (i.e. Thanksgiving).  That's it for now, more later...



3 comments:

  1. Finish it so we can use the g-d thing!

    ReplyDelete
  2. Hey Mike, I really hope that you have had a chance to enjoy your teardrop trailer. I've been reading your blog, and I really like some of the things that you have done, and I would like to incorporate a couple of them into my 5x8 teardrop build. I really appreciate the links you included in your narrative. I plan on enjoying my teardrop with my wife and two boys, one 3 1/2 years, the other 14 months. My plan is to build in a bunk bed, so that one or both will sleep on that. Thanks again for your tips! Happy travels!

    ReplyDelete